TruckBusWorld

Federal driving rules for US truck and bus drivers: Part 392

Buses with passengers stop 15 to 50 feet from rail tracks; no texting or hand-held phone use while driving; truck riders need written authorization.

Published · Last updated

Passive railroad grade crossing on an unpaved rural road in Arizona at dusk, with two white crossbuck signs reading Rail Road Crossing beside the track
YosemiteYamper — CC BY-SA 4.0

Part 392 of the Federal Motor Carrier Safety Regulations sets the federal rules for driving a commercial motor vehicle in interstate commerce in the United States. A bus transporting passengers, and certain hazardous materials vehicles and cargo tanks, must stop within 50 feet of, and not closer than 15 feet to, the tracks before crossing them; a driver may not text or use a hand-held mobile telephone while driving except to contact law enforcement or emergency services; apart from listed exceptions, a commercial motor vehicle other than a bus may carry other persons only with the motor carrier’s written authorization; and a driver may neither use a radar detector in a commercial motor vehicle nor operate a commercial motor vehicle that is equipped with or contains one. School bus operations are outside these rules except for the texting and phone bans and a few other listed provisions.

Status: 14 November 2026. This page follows sections 392.5, 392.10, 392.11, 392.12, 392.15, 392.16, 392.22, 392.60, 392.71, 392.80 and 392.82, together with sections 383.51 and 390.3T, of Title 49 of the Code of Federal Regulations in the annual edition revised as of October 1, 2025. Paragraphs (b)(2)(i) and (ii) of section 392.22 are given in the wording of the final rule of February 19, 2026 (91 FR 7867), in force since March 23, 2026, which this edition does not yet print. The Federal Register’s list of documents affecting Part 392 published from September 1, 2025 to November 14, 2026 shows that rule and the notification of data availability of March 27, 2026 (91 FR 14803) on a proposed change to section 392.10, and no other document. Federal Motor Vehicle Safety Standard No. 208 (49 CFR 571.208) is read in the edition revised as of October 1, 2025, with the interim final rule of April 6, 2026 (91 FR 17144), the only rule with that standard in its title in the Federal Register’s list of rules affecting Part 571 published from September 1, 2025 to November 14, 2026. These are the federal rules; State traffic codes and fines are not described here, apart from one Minnesota statute cited for school buses.

The Part 392 rules on this page at a glance (49 CFR, edition revised as of October 1, 2025, with 91 FR 7867).
SubjectWhat the text requiresSection
Railroad crossings, stop requiredBuses transporting passengers, certain hazardous materials vehicles and cargo tanks stop within 50 feet of, and not closer than 15 feet to, the tracks, and do not shift gears while crossing392.10
Railroad crossings, slowing and clearanceOther vehicles approach at a speed that permits stopping before the nearest rail; no vehicle drives onto a crossing without space to drive completely through392.11, 392.12
TextingNo texting while driving; exception to contact law enforcement or emergency services392.80
Hand-held mobile telephoneNo use while driving; same emergency exception392.82
Passengers in a truckWritten authorization from the motor carrier, except for assigned persons, emergency aid and livestock attendants; not required on a bus392.60
Seat beltsThe driver wears the installed belt; in property-carrying vehicles all other occupants too392.16
Stopped on the roadHazard flashers at once; three warning devices within 10 minutes392.22
Radar detectorsNo use, and no driving a vehicle that is equipped with or contains one392.71
AlcoholNone within 4 hours before going on duty or driving; 24 hours out of service for a violation392.5

Who the rules apply to

Section 390.3T(a)(1) makes the rules of this subchapter, Part 392 among them, “applicable to all employers, employees, and commercial motor vehicles that transport property or passengers in interstate commerce.” Paragraph (f) opens with “Unless otherwise specifically provided” and lists what they do not apply to. Among the exceptions:

  • (1) all school bus operations as defined in section 390.5T, “except for §§ 391.15(e) and (f), 392.15, 392.80, and 392.82”;
  • (2) transportation performed by the Federal government, a State, a political subdivision of a State, or an agency established under an interstate compact approved by Congress;
  • (5) fire trucks and rescue vehicles while involved in emergency and related operations;
  • (6) vehicles designed or used to transport between 9 and 15 passengers (including the driver), not for direct compensation, that do not otherwise meet the definition of a commercial motor vehicle; their motor carriers and drivers must still comply with, among others, sections 392.80 and 392.82.

Section 392.15 bars a driver who holds a commercial learner’s permit or a CDL from operating a commercial motor vehicle if prohibited by section 382.501(a); that rule and the Clearinghouse behind it are described in the FMCSA Drug and Alcohol Clearinghouse.

Why do buses stop at railroad tracks?

Because section 392.10 requires it. Except at the crossings listed below, the driver of a vehicle in one of six groups shall not cross a railroad track at grade unless he or she first stops the vehicle “within 50 feet of, and not closer than 15 feet to, the tracks”, then listens and looks in each direction along the tracks for an approaching train and ascertains that no train is approaching. When it is safe, the driver crosses in a gear that permits the vehicle to complete the crossing without a change of gears: “The driver must not shift gears while crossing the tracks.”

The six groups in paragraph (a) are:

  1. every bus transporting passengers;
  2. every commercial motor vehicle transporting any quantity of a Division 2.3 chlorine;
  3. every commercial motor vehicle that must be marked or placarded with one of the classifications listed in items (i) to (xviii) of the paragraph, which include Divisions 1.1 to 1.4, 2.1, 2.2, 2.3, 4.1, 4.3, 5.1, 5.2 and 6.1 and Classes 3, 7 and 8 (the placards themselves are described in hazmat placards and the hazmat endorsement);
  4. every cargo tank motor vehicle, whether loaded or empty, used for the transportation of any hazardous material as defined in Parts 107 to 180;
  5. every cargo tank motor vehicle transporting a commodity which at the time of loading has a temperature above its flashpoint;
  6. every cargo tank motor vehicle, whether loaded or empty, transporting any commodity under exemption under subpart B of Part 107.

Under paragraph (b) a stop need not be made at a streetcar crossing or at tracks used exclusively for industrial switching within a business district; when a police officer or crossing flagman directs traffic to proceed; at a crossing controlled by a functioning highway traffic signal showing a green indication which, under local law, permits the vehicle to proceed without slowing or stopping; at an abandoned crossing marked with a sign saying the line is abandoned; or at an industrial or spur line crossing marked with a sign reading “Exempt”, which may be erected only by or with the consent of the appropriate State or local authority.

Every other commercial motor vehicle approaching a crossing is driven at a speed that permits it “to be stopped before reaching the nearest rail” and is not driven over the crossing until due caution has been taken to ascertain that the course is clear (section 392.11). For all of them, section 392.12 adds: “No driver of a commercial motor vehicle shall drive onto a highway-rail grade crossing without having sufficient space to drive completely through the crossing without stopping.”

School buses and railroad crossings

The stop that school buses make is not required by section 392.10. Section 390.3T(f)(1) takes school bus operations out of the federal motor carrier safety rules except for sections 391.15(e) and (f), 392.15, 392.80 and 392.82, and section 392.10 is not among them. The stop is a matter for State law. In Minnesota, for example, section 169.28 of the 2026 Minnesota Statutes requires the driver “of any school bus whether carrying passengers or not” to stop the vehicle “not less than 15 feet nor more than 50 feet from the nearest rail”, and not to shift gears while crossing; the same paragraph also covers motor vehicles carrying passengers for hire, Head Start buses and any vehicle that must stop under section 392.10, while paragraph (c) exempts a type III vehicle from the school bus stop. The laws of the other States are not described here. School bus types and the federal standards for the vehicles are in school bus types and dimensions.

The proposed exception for crossings with active warning devices

Section 392.10 is in force as quoted above. A change to it is pending in docket FMCSA-2021-0050 (RIN 2126-AC39), and it is a proposal only:

  • May 30, 2025: the Federal Motor Carrier Safety Administration (FMCSA) published a notice of proposed rulemaking (90 FR 22914). In FMCSA’s later summary, it proposed adding an exception for any crossing “equipped with an active warning device that is not in an activated state”, which under local law would permit the vehicle to proceed without slowing or stopping. Comments closed on July 29, 2025.
  • March 27, 2026: a notification of data availability (91 FR 14803) said that FMCSA had summarized information from Federal Railroad Administration data on vehicle and railroad collisions, rear-end fatal crashes of commercial motor vehicles and signal failures and posted it to the docket, with comments due by April 27, 2026. It says: “The Agency may consider this information in preparation of further regulatory action.”
  • November 14, 2026: the Federal Register list of documents affecting Part 392 shows no final rule in this proceeding.

Crossing offenses and the CDL

Table 3 of section 383.51 lists six railroad-highway grade crossing offenses for which a person required to have a commercial learner’s permit or a CDL, and any holder of one, is disqualified when convicted of operating a commercial motor vehicle in violation of a Federal, State or local law. They include failing to slow down and check that the tracks are clear when the driver is not required to always stop, failing to stop when the driver “is always required to stop”, failing to have sufficient space to drive completely through the crossing, and failing to negotiate a crossing because of insufficient undercarriage clearance. For each, the disqualification is no less than 60 days for a first conviction, no less than 120 days for a second, and no less than 1 year for a third or subsequent conviction, the second and later ones counting any combination of these offenses in a separate incident within a 3-year period. The license classes themselves are described in CDL classes and endorsements. The other three tables of section 383.51, on major offenses, serious traffic violations and out-of-service orders, are described in CDL disqualifications.

The texting and hand-held phone rules for CDL drivers

Section 392.80(a) reads: “No driver shall engage in texting while driving.” Section 392.82(a)(1) reads: “No driver shall use a hand-held mobile telephone while driving a CMV.” In both sections the motor carrier may not allow or require its drivers to do so. Both also apply to school bus operations and to the 9 to 15 passenger vehicles described above.

Each section defines driving for its own purpose only:

  • Texting (392.80(c)): operating a commercial motor vehicle “with the motor running, including while temporarily stationary because of traffic, a traffic control device, or other momentary delays”.
  • Hand-held phone (392.82(b)): operating a commercial motor vehicle “on a highway”, including while temporarily stationary for the same reasons.

In neither section does driving include operating a vehicle that the driver has moved to the side of, or off, a highway and halted where it can safely remain stationary; for texting this applies with or without the motor running. Both sections permit the activity “when necessary to communicate with law enforcement officials or other emergency services” (392.80(d), 392.82(c)). What counts as texting or as using a hand-held mobile telephone is not covered here.

Section 383.51 links convictions under State and local texting and hand-held phone laws to the CDL. Rows (9) and (10) of its Table 2 list violating a State or local law or ordinance on motor vehicle traffic control that prohibits texting, or that restricts or prohibits the use of a hand-held mobile telephone, while driving a CMV. Table 2 sets a period only for repeat convictions of any combination of its offenses, which also include speeding by 15 mph or more above the limit and reckless driving: for a second conviction in a separate incident within a 3-year period while operating a CMV, 60 days; for a third or subsequent one, 120 days. For rows (9) and (10), the columns for convictions in a non-commercial vehicle read “Not applicable”.

Can truck drivers have passengers?

Only on the terms of section 392.60. Unless specifically authorized in writing by the motor carrier under whose authority the vehicle is operated, “no driver shall transport any person or permit any person to be transported on any commercial motor vehicle other than a bus.” The authorization states the name of the person to be transported, the points where the transportation is to begin and end, and the date upon which the authority expires.

No written authorization is needed for:

  • employees or other persons assigned to a commercial motor vehicle by a motor carrier;
  • any person transported when aid is being rendered in case of an accident or other emergency;
  • an attendant delegated to care for livestock.

The section names no separate rule for a spouse or other family member. Under paragraph (b) it does not apply to commercial motor vehicles controlled and operated by a farmer and used to carry agricultural commodities or products from the farm, or supplies to it. Buses are outside the section altogether, since it applies only to vehicles “other than a bus”. An authorized rider in a property-carrying vehicle also falls under the seat belt rule below.

Seat belts, and what FMVSS No. 208 requires in a truck cab

Section 392.16 has two paragraphs. Under (a), no driver shall operate a commercial motor vehicle that has a seat belt assembly installed at the driver’s seat “unless the driver is properly restrained by the seat belt assembly”, and no motor carrier shall require or permit it. Under (b), the same applies to the other occupants of a property-carrying commercial motor vehicle that has seat belt assemblies installed at their seats: all of them must be properly restrained. The section does not address bus passengers.

Occupant crash protection in new trucks is the subject of Federal Motor Vehicle Safety Standard No. 208, “Occupant crash protection” (49 CFR 571.208). Under S3(a) it applies to passenger cars, multipurpose passenger vehicles, “trucks designed to carry at least one person, and buses.” Its requirements change with the vehicle’s gross vehicle weight rating (GVWR).

Occupant protection required in trucks by FMVSS No. 208, at the two ends of the weight range (49 CFR 571.208, edition revised as of October 1, 2025).
VehicleWhat the standard requiresParagraph
Trucks, buses and multipurpose passenger vehicles with a GVWR of 8,500 pounds (3,855 kg) or less and an unloaded weight of 5,500 pounds (2,495 kg) or less, made on or after September 1, 1997 (S4.2.6); the air bag requirement of S4.2.6.2 applies to each such vehicle made on or after September 1, 1998The passenger car requirements of S4.1.5.1, with frontal crash protection by means of an inflatable restraint system, defined as “an air bag that is activated in a crash”, at the driver’s and right front passenger’s position; under S4.2.6, walk-in van-type trucks and vehicles designed to be sold exclusively to the U.S. Postal Service may meet S4.2.1.1 or S4.2.1.2 instead of S4.1.5.1S4.2.6, S4.2.6.2, S4.1.5.1
Trucks and multipurpose passenger vehicles with a GVWR of more than 10,000 pounds (4,536 kg), made on or after September 1, 1990Either the first option, the crash protection requirements of S5 “by means that require no action by vehicle occupants”, or the second option, a Type 1 or Type 2 seat belt assembly at each designated seating position; a Type 1 belt or the pelvic portion of a dual retractor Type 2 belt at a front outboard seat has an emergency locking or automatic locking retractorS4.3.2, S4.3.2.1, S4.3.2.2

A protection system that meets the first option “may be installed at one or more designated seating positions” of a heavy truck that otherwise meets the belt option (S4.3.2). The belt option refers to Standard No. 209 and to S7.2, the latch mechanism of FMVSS No. 208, and not to S7.3, its seat belt warning system. The rules for trucks between 8,500 and 10,000 pounds GVWR are not covered here.

Seat belt warnings, for vehicles up to 10,000 pounds only. A final rule of January 3, 2025 (90 FR 390) required rear-seat belt warnings and extended the driver’s seat belt warning to the front outboard passenger seat for passenger cars, trucks, most buses and multipurpose passenger vehicles with a GVWR of 10,000 pounds or less, with some exceptions, with compliance dates of September 1, 2026 for the front seats and September 1, 2027 for the rear seats; the edition revised as of October 1, 2025 prints those dates. The interim final rule of April 6, 2026 (91 FR 17144, docket NHTSA-2026-0727), effective that day, delays them: “The compliance date of this interim final rule is September 1, 2028, with optional early compliance permitted.” Multi-stage manufacturers and alterers have an additional year. Comments were due by May 21, 2026; the National Highway Traffic Safety Administration states that following the close of the comment period it “will publish a final rule responding to any comments received”. The Federal Register’s list of rules affecting Part 571 published from September 1, 2025 to November 14, 2026 shows no later rule with Occupant Crash Protection in its title. The rule does not change the requirements for trucks of more than 10,000 pounds GVWR.

Warning devices when a truck or bus stops on the road

Under section 392.22(a), whenever a commercial motor vehicle is stopped on the traveled portion or the shoulder of a highway for any cause other than necessary traffic stops, the driver “shall immediately activate the vehicular hazard warning signal flashers” and keep them flashing until the warning devices are placed, and again while the devices are picked up before the vehicle moves. The flashers may be used in addition to, “but not in lieu of”, the devices. Paragraph (b)(1) then requires the driver to place the warning devices required by section 393.95 “as soon as possible, but in any event within 10 minutes”.

Placement of warning devices under 49 CFR 392.22(b), with paragraphs (b)(2)(i) and (ii) as amended by 91 FR 7867 from March 23, 2026.
SituationWhat the text requiresParagraph
General ruleOne on the traffic side, 4 paces (approximately 3 meters or 10 feet) from the vehicle toward approaching traffic; one at 40 paces (approximately 30 meters or 100 feet) toward approaching traffic and one at 40 paces away from it, both in the center of the lane or shoulder the vehicle occupies(b)(1)
Fusees onlyA lighted fusee at each location, at least one lighted at each as long as the vehicle is stopped; each one extinguished and removed before the vehicle moves(b)(2)(i)
Daylight hoursThree bidirectional reflective triangles or three lighted fusees within 10 minutes; a driver who uses only fusees keeps at least one lighted at each location while stopped or parked(b)(2)(ii)
Business or residential districtNot required, except while lighted lamps are required and street or highway lighting does not make the vehicle clearly discernable at 500 feet(b)(2)(iii)
Within 500 feet of a curve, hill crest or other obstruction to viewThe warning signal placed in the direction of the obstruction, 100 to 500 feet from the vehicle(b)(2)(iv)
Divided or one-way highwayOne device at 200 feet and one at 100 feet toward approaching traffic, in the center of the lane or shoulder; one at the traffic side within 10 feet of the rear(b)(2)(v)
Leaking flammable liquid or gasNo flame-producing signal except at a distance that assures the prevention of a fire or explosion(b)(2)(vi)

What changed on March 23, 2026. The final rule of February 19, 2026 (91 FR 7867, docket FMCSA-2025-0110) removed the references to liquid-burning flares from the warning device requirements of Parts 392 and 393. Paragraph (b)(2)(i), formerly headed “Fusees and liquid-burning flares”, now reads in its first sentence: “The driver of a commercial motor vehicle equipped with only fusees shall place a lighted fusee at each of the locations specified in paragraph (b)(1) of this section.” Paragraph (b)(2)(ii) now names “three bidirectional reflective triangles or three lighted fusees”. FMCSA gave its reason in the summary: the rule “eliminates outdated language referring to warning devices that FMCSA believes are no longer used.” The edition revised as of October 1, 2025 still prints the old wording.

Radar detectors

Section 392.71 has two paragraphs. Paragraph (a): “No driver shall use a radar detector in a commercial motor vehicle, or operate a commercial motor vehicle that is equipped with or contains any radar detector.” Paragraph (b): “No motor carrier shall require or permit a driver to violate paragraph (a) of this section.” Paragraph (a) is not limited to use: its second half covers operating a vehicle that is equipped with or contains a detector.

Alcohol in the four hours before duty

Section 392.5(a) says no driver shall use alcohol, or be under the influence of alcohol, “within 4 hours before going on duty or operating, or having physical control of, a commercial motor vehicle”; shall use alcohol or have any measured alcohol concentration or detected presence of alcohol while on duty or driving; or shall be on duty or drive while possessing wine, beer or distilled spirits. The possession rule does not apply to alcohol manifested and transported as part of a shipment, or possessed or used by bus passengers (paragraph (a)(3)). A motor carrier may not require or permit a violation, nor require or permit a driver to be on duty or drive if, by the driver’s general appearance or conduct or by other substantiating evidence, the driver appears to have used alcohol within the preceding four hours.

A driver found in violation “shall be placed out-of-service immediately for a period of 24 hours” (paragraph (c)). The driver reports the order to the employer within 24 hours, and to a State official designated by the State that issued the driver’s license within 30 days or, where the driver requests a review, within 30 days of an affirmation of the order; a petition for review may be submitted in writing within 10 days of the issuance of the order (paragraphs (d) and (e)).

What this page does not cover

  • The other sections of Part 392, among them section 392.7, described in pre-trip inspection and the DVIR.
  • Limits on driving and on-duty time, which are in Part 395 and described in hours of service.
  • Which warning devices a vehicle must carry (section 393.95) and the other equipment rules of Part 393.
  • The definitions of section 390.5T, State traffic laws other than the Minnesota statute cited, fines and civil penalties.

Quick answers

Why do buses stop at railroad tracks?
Because 49 CFR 392.10 requires every bus transporting passengers in interstate commerce, outside the exceptions of 49 CFR 390.3T(f), to stop within 50 feet of, and not closer than 15 feet to, the tracks, then listen and look in each direction for an approaching train before crossing. The bus then crosses in a gear that lets it finish without changing gears; the driver must not shift gears while crossing. No stop is required where a police officer or flagman directs traffic to proceed, at a green traffic signal that under local law permits crossing without stopping, at an abandoned crossing marked as such, at an industrial or spur line crossing signed “Exempt”, or at a streetcar crossing or tracks used exclusively for industrial switching within a business district.
Why do school buses stop at railroad crossings?
Not because of section 392.10. Under 49 CFR 390.3T(f)(1) the federal motor carrier safety rules do not apply to school bus operations, except for sections 391.15(e) and (f), 392.15, 392.80 and 392.82. The stop is a matter for State law. Minnesota Statutes section 169.28, for example, requires the driver of any school bus, whether carrying passengers or not, to stop not less than 15 feet nor more than 50 feet from the nearest rail.
Can truck drivers have passengers?
Only with the motor carrier's written authorization. Section 392.60 bars a driver from transporting any person on a commercial motor vehicle other than a bus unless the carrier has authorized it in writing, naming the person, the points where the transportation begins and ends, and the date the authority expires. No authorization is needed for employees or other persons the carrier assigns to the vehicle, for someone carried while aid is given after an accident or other emergency, or for an attendant caring for livestock. Under paragraph (b) the section does not apply to commercial motor vehicles controlled and operated by a farmer and used to carry agricultural commodities or products from the farm, or supplies to it. The section names no separate rule for family members.
Can CDL drivers text or use a cell phone while driving?
Not for texting or hand-held phone use. Sections 392.80 and 392.82 forbid texting and using a hand-held mobile telephone while driving, and forbid motor carriers to allow or require it; both apply to school bus operations too. Both permit it when necessary to communicate with law enforcement officials or other emergency services. Table 2 of 49 CFR 383.51 lists State or local texting and hand-held phone offenses while driving a commercial motor vehicle among its serious traffic violations: a second conviction for any combination of the offenses in that table, in a separate incident within 3 years while operating a commercial motor vehicle, disqualifies the driver for 60 days, a third or subsequent one for 120 days.
Can you have a radar detector in a commercial motor vehicle?
No. Section 392.71(a) says no driver shall use a radar detector in a commercial motor vehicle, or operate a commercial motor vehicle that is equipped with or contains any radar detector. Paragraph (b) forbids a motor carrier to require or permit a driver to violate that rule. The ban is not limited to use: it also covers operating a vehicle that contains a detector.
Do semi trucks have airbags?
Federal Motor Vehicle Safety Standard No. 208 does not require one in trucks with a gross vehicle weight rating of more than 10,000 pounds. Such trucks made on or after September 1, 1990 meet either a crash protection requirement “by means that require no action by vehicle occupants” or a belt option with a Type 1 or Type 2 seat belt at each designated seating position (S4.3.2). The standard's air bag requirement in S4.2.6.2 covers trucks of 8,500 pounds GVWR or less with an unloaded weight of 5,500 pounds or less, made on or after September 1, 1998. The driver must wear the belt that is installed (49 CFR 392.16).

Sources

  1. 49 CFR Part 392 — Driving of Commercial Motor Vehicles, sections 392.5 to 392.82 (Code of Federal Regulations, annual edition revised as of October 1, 2025) — U.S. Government Publishing Office (govinfo)
  2. Parts and Accessories Necessary for Safe Operation; Liquid-Burning Flares — final rule, 91 FR 7867 (February 19, 2026), effective March 23, 2026 — Federal Motor Carrier Safety Administration (Federal Register, govinfo), 19 Feb 2026
  3. Railroad Grade Crossings; Stopping Required: Exception for Railroad Grade Crossing Equipped With Active Warning Device Not in Activated State — notification of data availability, 91 FR 14803 (March 27, 2026) — Federal Motor Carrier Safety Administration (Federal Register, govinfo), 27 Mar 2026
  4. Federal Register documents affecting 49 CFR Part 392 published since September 1, 2025 (list read on November 14, 2026) — Office of the Federal Register (federalregister.gov)
  5. 49 CFR 390.3T — General applicability (Code of Federal Regulations, annual edition revised as of October 1, 2025) — U.S. Government Publishing Office (govinfo)
  6. 49 CFR 383.51, Tables 2 and 3 — disqualification for serious traffic violations and for railroad-highway grade crossing offenses (Code of Federal Regulations, annual edition revised as of October 1, 2025) — U.S. Government Publishing Office (govinfo)
  7. 49 CFR 571.208 — Standard No. 208; Occupant crash protection (Code of Federal Regulations, annual edition revised as of October 1, 2025) — U.S. Government Publishing Office (govinfo)
  8. Federal Motor Vehicle Safety Standards; Occupant Crash Protection, Seat Belt Reminder Systems — interim final rule, 91 FR 17144 (April 6, 2026), effective April 6, 2026 — National Highway Traffic Safety Administration (Federal Register), 6 Apr 2026
  9. Federal Register rules affecting 49 CFR Part 571 published since September 1, 2025 (list read on November 14, 2026) — Office of the Federal Register (federalregister.gov)
  10. Minnesota Statutes 2026, section 169.28 — Certain vehicles to stop at railroad crossing — Minnesota Office of the Revisor of Statutes