TruckBusWorld

HGV, bus and trailer roadworthiness in Great Britain

Walkaround check before use, safety inspections normally every 4 to 13 weeks, brake tests, the annual test and ministry plates, as DVSA and GOV.UK set them out for GB.

Published · Last updated

Two articulated lorries, a Volvo and an orange Scania, parked in a roadside lorry park at Girvan in Scotland, with green hills behind
Billy McCrorie (plate blurred) — CC BY-SA 2.0 (cropped)

DVSA’s Guide to maintaining roadworthiness names two main types of inspection for lorries, buses and coaches in Great Britain: a walkaround check before the vehicle is used on the public highway, and safety inspections at the frequency the operator has recorded on the vehicle operator licensing service (VOL). Alongside them, GOV.UK lists the HGVs, buses and trailers that need the annual test. The Guide says an inspection frequency “would normally range between 4 to 13 weeks”, and that drivers’ defect reports and safety inspection records must be kept for at least 15 months. Goods vehicles and trailers that need the annual test must also have a ministry plate and a plating certificate.

This article follows what DVSA and GOV.UK publish for England, Scotland and Wales: the Guide to maintaining roadworthiness, which shows “Updated 28 April 2025”; DVSA’s walkaround check pages for HGVs and for buses and coaches; GOV.UK’s overview of the HGV, bus and trailer MOT; and DVSA’s guidance on ministry plates, updated on 1 June 2026. Northern Ireland is not covered here. The operator licences behind these duties are in goods vehicle operator licences in Great Britain and PSV operator licences, and the EU testing framework is in roadworthiness tests and roadside checks. The pages were read on 13 November 2026, and the figures are those pages’ figures on that date.

Roadworthiness in Great Britain in brief. Sources: DVSA, Guide to maintaining roadworthiness (updated 28 April 2025), with section numbers; GOV.UK, HGV, bus and trailer MOT overview; DVSA, ministry plates guidance (updated 1 June 2026).
ItemAs the sources state it
Walkaround checkMust be done before the vehicle is used on the public highway; at least one in every 24-hour period in service (Guide 1.4 and section 3)
Defect reports and inspection recordsKept for at least 15 months (Guide 1.5)
Safety inspection frequencyMust follow the frequency recorded on VOL; the Guide’s examples normally range from 4 to 13 weeks, with 6 weeks for vehicles and trailers 12 years or older (Guide 1.5 and 4.2)
Brake performanceExpected at every safety inspection; without EBPMS, a minimum of four laden brake tests a year, which can include the annual test (Guide 5.3)
Annual testHGVs and buses usually each year, the first 12 months after first DVLA registration; trailers usually one year after first sold or supplied (GOV.UK)
Ministry platesHGVs and trailers that require an annual MOT: plates VTG 6A and VTG 6T, certificates VTG 7A and VTG 7T; £27 to update after a notifiable alteration (DVSA)

What the Guide means by “must” and “should”

The Guide sorts its own sentences into two kinds (section 1.1). Where it says “must”, it is “a direct legal requirement set out in legislation, something that is required under Road Traffic law, Health and Safety legislation, or the legal undertakings to the Traffic Commissioner for your operator licence”. Where it says “should”, it is “best practice”, which the Guide says operators are not required to follow, though it is “strongly recommended” unless an alternative approach can be shown to provide a similar level of compliance. The Guide states that the Upper Tribunal, “the Traffic Commissioners’ appeal court”, has approved it for managing maintenance, and that Traffic Commissioners rely on it “as the starting point” for whether arrangements are “satisfactory” and “suitable”.

The licensing duties the Guide cites are, for goods operators, section 13C(4) of the Goods Vehicles (Licensing of Operators) Act 1995, which it quotes as requiring that “there must be satisfactory facilities and arrangements for maintaining the vehicles used under the licence in a fit and serviceable condition”, and, for passenger operators, section 14ZC(1) of the Public Passenger Vehicles Act 1981, which it quotes as requiring that the traffic commissioner is satisfied that there will be “adequate facilities or arrangements for maintaining in a fit and serviceable condition the vehicles proposed to be used under the licence”. Both are given here as the Guide quotes them; the Acts were not read for this article.

Further points from the Guide’s opening sections:

  • Roadworthiness means complying with the appropriate vehicle construction, road safety, environmental and operating standards required by the law in the UK, and “For a driver and operator, it is a criminal offence to use an unroadworthy vehicle on the road.”
  • Wherever the Guide says “vehicle”, “this terminology equally applies to a trailer”. The user of a towing vehicle is responsible for the roadworthiness of a trailer even if it does not belong to them.
  • Operators are responsible for the condition of vehicles and trailers inspected or maintained for them by agents, contractors or hire companies, and an operator that contracts out its safety inspections must draw up a formal written contract and retain it on file.
  • If vehicles do not stay in a satisfactory condition, “Traffic Commissioners reserve the right to require more stringent arrangements from you (such as shorter periods between inspections)”.

The Guide uses “must” for the check itself and words its frequency two ways. Section 1.4: “A driver or designated responsible person must conduct a walkaround check of a vehicle prior to using the equipment on the public highway. At least one walkaround check should be carried out in every 24-hour period that the vehicle is in service.” The introduction to section 3: “A minimum of one walkaround check must be carried out every day or at least once in a 24-hour period that the vehicle is used.” The same section adds that vehicles engaged in arduous or off-road operations “may require multiple checks during the 24 hour period”.

What else the Guide says about the check:

  • The driver is always legally responsible for the condition of the vehicle while in use. Operators can delegate the check to a responsible person who may not be the driver, and the driver then needs to see evidence that the check has been completed.
  • Where several drivers use a vehicle in one day, a check at a driver change is not always safe, for example at a bus stop; the Guide accepts this where there is a robust driver defect reporting system covering the initial check and any defects or “nil” defects reported during the day.
  • Where trailers are changed on multiple occasions, the Guide says a check should be made on each trailer used.
  • Vehicles over 3 metres high must display an in-cab overall height indicator.
  • Drivers using tachograph records must record the walkaround check and any associated repairs as “other work” (section 3.2); the GB drivers’ hours rules are in drivers’ hours and tachograph rules in Great Britain.
  • Traffic Commissioners can take action against a driver who fails to complete an adequate walkaround check, which could lead to a driver conduct hearing and “may result in the loss of the vocational driving licence” (section 3.2).

A news story published by the Traffic Commissioners for Great Britain on 8 September 2025 (updated 18 September 2025) calls the check “a legal requirement and a vital safeguard for public safety”. It says the check “counts as working time, and drivers must be given adequate time to complete it properly.”

What DVSA’s walkaround pages list for lorries and for buses

The Guide points to two DVSA pages for the check items. Both say a defect is reported “in writing to the person in charge of sorting out vehicle defects in your organisation”. The headings below are DVSA’s own; each item on DVSA’s pages carries further detail.

Lorries. “Carry out HGV daily walkaround checks” (published 20 September 2019, last updated 21 September 2023, applying to England, Scotland and Wales) numbers 27 items:

  • Inside the vehicle, items 1 to 9: front view (mirrors, cameras and glass); windscreen wipers and washers; dashboard warning lights and gauges; steering; horn; brakes and air build-up; height marker; seatbelts; security and condition of cab, doors and steps.
  • Outside the vehicle, items 10 to 27: lights and indicators; fuel and oil leaks; security of body and wings; battery security and conditions; diesel exhaust fluid (AdBlue); excessive engine exhaust smoke; high voltage emergency cut-off switch; alternative fuel systems and isolation; spray suppression; tyres and wheel fixing; brake lines and trailer parking brake; electrical connections; coupling security; security of load; number plate; reflectors; markings and warning plates; other equipment.

Buses and coaches. “Carry out bus or coach daily walkaround checks” (published 28 April 2021, last updated 18 April 2023) numbers 29 items:

  • From the driver’s seat, items 1 to 9: front view (mirrors, cameras, glass, and visibility); windscreen wipers and washers; warning lamps; steering; horn; brake and air build-up; height marker; electronic ticket machine; driver’s seat belt and cab interior.
  • Inside the vehicle, items 10 to 18: doors and exits; accessibility equipment; seats and seat belts; communication with the driver; heating and ventilation; emergency exit hammer; fire extinguisher; first aid kit; body interior.
  • Outside the vehicle, items 19 to 29: tyre and wheel fixing; lights, indicators, side repeaters and reflectors; number plate; body exterior; fuel, oil and waste leaks; excessive engine exhaust smoke; diesel exhaust fluid (AdBlue); battery (if easily accessible); ancillary equipment; high voltage emergency cut-off switch; alternative fuel systems and isolation.

Some figures on these pages: both give a tyre tread depth “of at least 1mm”. The bus page says a vehicle covered by the Public Service Vehicle Accessibility Regulations “must” have its accessibility features checked, among them the wheelchair space, the boarding device, priority seats and handrails. It says the fire extinguisher must contain water or foam, be marked BS 5423 or EN3 and have a minimum fire rating of at least 8A or 21B, and that a first aid kit is needed on a bus with 16 or more passenger seats (except local services) or with 9 to 16 passenger seats first used from 1 April 1988. The high-voltage and alternative-fuel items were added to both lists on 18 April 2023; what they say for electric vehicles is in electric-truck maintenance compared with diesel.

Recording and reporting defects

Both DVSA pages list what the record contains: the vehicle registration or identification mark, the date, details of the defects or symptoms, the assessment of the defects (for example “dangerous”), the name of the person reporting and who it was reported to. They add: “Use a form that includes a list of the items checked each day. Record ‘nil’ defects if you do not find any.” The HGV page says “DVSA can ask for a record of your walkaround check at a roadside check.” On defects found during a journey, both say dangerous defects must be fixed before the journey continues, and that using the vehicle in a dangerous condition can bring an unlimited fine and a prison sentence.

The Guide (section 3.1) says any defects found during the check, while the vehicle is in use or on its return to base, “must be the subject of a written report”, and adds the rectification work and the date it was completed to the details recorded. On keeping the records:

  • Drivers’ defect reports used to record any faults and rectification work must be kept for at least 15 months (section 1.5).
  • Electronic records of reported defects are acceptable and “must be available for 15 months, along with any record of repair” (section 3.1).
  • “It is recommended that ‘nil’ defect reports are retained for at least 3 months” (section 3.1).
  • For an owner-driver with no one to report defects to, the Guide says defects and the remedial action taken “can simply be recorded and held for at least 15 months”.

Safety inspections: what they cover and how often

The Guide defines a safety inspection as “a periodic inspection that is carried out at pre-set intervals in line with what an operator has declared on the vehicle operator licensing service” (section 1.4). Two related checks have their own rules there. Before a newly acquired vehicle is used on the public highway, operators must conduct a first use inspection, and the Guide says its scope should at least include all the items inspected at annual test, including a laden roller brake test when appropriate for the type of vehicle. An intermediate safety check covers components that may need checking more often than at full inspections; the Guide says it should be documented and marked as such.

The “must” sentences of the Guide’s key points (section 1.5):

  • Operators “must ensure that safety inspections are carried out at the stated frequency as it is recorded on the vehicle operator licensing service”. Any change to the arrangements must be updated on VOL.
  • “Safety inspections must include those items covered by the appropriate statutory annual test.” Section 4.1 adds that the standards for the annual test “are the minimum legal standards and should be used as guidance for the safety inspection”.
  • Safety inspection records must be fully completed and the vehicle declared roadworthy before it returns to service, and the transport manager or responsible person must have access to and review the completed record before then.
  • “Records of safety inspections must be kept for at least 15 months for all vehicles”, including vehicles removed from the operator licence, sold or otherwise disposed of.

The Guide lists what a safety inspection record should at least include: name of operator, date and location of the inspection, the organisation that carried it out, vehicle identity, make and model, odometer reading if appropriate, a list of all the inspection manual items to be inspected, details of any defects, name of inspector, complete details of any repair work and who did it, and a signed declaration that any defects have been repaired satisfactorily and the vehicle is now in a safe roadworthy condition. It also says inspection dates should be identified at least 6 months in advance on a planner or wall chart.

The 4 to 13 week table

Section 4.2 says the frequency should be set by assessing the mechanical deterioration a vehicle is likely to incur, from factors such as its age and type, the manufacturer’s recommendations, its load, its operations, the terrain and the distances, speeds and journey times. It then gives “A guide to safety inspection intervals”: “An inspection frequency would normally range between 4 to 13 weeks.”

The Guide’s examples of operating conditions and inspection frequencies (section 4.2, “A guide to safety inspection intervals”). Guidance, not a statutory interval: the Guide says operators must keep to the frequency recorded on VOL.
Operating conditionsFrequency
A. Lightly loaded vehicles, easy operating conditions10-13 weeks
B. General haulage, trunking6-10 weeks
C. Arduous work, constant heavy loads4-6 weeks
D. Off road, difficult conditions4 weeks
E. Vehicle or trailer 12 years or older6 weeks

The Guide’s words on the rows and around them:

  • Older vehicles: the guidance “has indicated a minimum safety inspection frequency of 6 weeks requirement for vehicles and trailers aged 12 years and older”, and “depending on usage, such as low mileage and light conditions, the frequency may be extended.”
  • Mileage-based programmes “will need to be linked to time”. Because VOL records a time-based frequency, “the expected maximum equivalent time-frequency should be entered into the system (up to 13 weeks)” and the mixed frequency box ticked.
  • Third-party trailers not on the operator’s own frequency (section 3.2): “as a default position the inspection frequency should not exceed 13 weeks.”
  • Planning by week: the Guide states that “it is recommended” that the ISO week numbering system is used, with each inspection completed within the ISO week it falls in. In its example of a 6-week interval starting in week 10, inspections fall in weeks 16, 22, 28 and so on, and an early inspection in week 20 followed by an 8-week gap to week 28 “would not be permissible”.
  • “Vehicles that are only used for part of the year, or that have been out of service for some time, must be inspected before they are brought back into service.”

Brake testing at safety inspections

The braking duty the Guide cites for the operator’s licence is Regulation 18(1) of the Road Vehicles (Construction and Use) Regulations 1986, which it quotes: “Every part of every braking system and of the means of operation thereof fitted to a vehicle shall be maintained in good and efficient working order and be properly adjusted.” It adds that “fit and serviceable” may at times go beyond the basic annual test standard, giving brake performance as its example, and that “means of operation” also brings Advanced Driver Assistance Systems (ADAS) within scope.

Section 5.3 sets out the brake assessment:

  • “there is an expectation that every safety inspection will include a brake performance assessment”, using either a roller brake test (RBT), a suitable electronic braking performance monitoring system (EBPMS) or a decelerometer with temperature readings. Operators must satisfy themselves that the methods used meet Regulation 18.
  • Vehicles can be presented for roller brake testing up to 14 days before the safety inspection date; a copy of the report must be retained on the vehicle’s maintenance file.
  • “At present, EBPMS is only available for use on trailers.” Where it is used, a competent person must evaluate the performance report before every safety inspection, and the evaluation must be signed, dated and attached to the vehicle record.
  • “Where EBPMS is not used, it is expected there will be a minimum of four laden brake tests spread evenly across the year, this can include the annual test.”
  • An approved and calibrated decelerometer is acceptable for vehicles without trailers or vehicles that cannot be tested on an RBT, but “Decelerometers cannot be used for testing trailer brake performance.”
  • Where operators have problems with braking performance at annual test, roadworthiness inspections or in operation, a laden roller brake test must be carried out before the vehicle can be considered roadworthy.

Passenger carrying vehicles. “It is expected that an unladen RBT will be conducted at every safety inspection.” An operator that has assessed the risks and decides to use decelerometer assessments “must carry out a minimum of four roller brake tests spread evenly across the year (this can include the annual test)”.

Risk assessments. When a laden brake test is not conducted or EBPMS is not available, a risk assessment must be completed by a competent person who understands braking systems and components, and evaluated at every safety inspection without a laden test. A single risk assessment may be used where no change in the use of the vehicle is anticipated during a twelve-month period. “Risk assessments must be retained with the vehicle maintenance documents for 15 months and produced if required.” The Guide’s list of acceptable reasons for not carrying out a laden brake assessment, which it says “is not an exhaustive list”, covers unladen tri-axle semi-trailers and other vehicles that run at less than 65% of the permitted axle weights more than 70% of the time, ADR vehicles only when the load is considered dangerous and specialist facilities are not available, livestock carriers where other means of loading are not possible, noxious load carriers only when designed and constructed for that purpose and unable to be loaded with an alternative product, furniture removal vehicles only when designed and constructed as such, vehicles operating at 50% or more of permitted axle weights when unladen, and vehicles whose construction or weight prevents the use of an RBT. It adds that “where possible every attempt must be made to conduct a laden roller brake test.”

The publication page’s update log records that a section “5.3a Braking performance assessment from April 2025” was added on 5 November 2024, and that on 28 April 2025 section 5.3 had its requirements “clarified”. The HTML edition read on 13 November 2026 has no heading numbered 5.3a; the rules above are from its section 5.3. The brake test of hybrid and electric lorries at DVSA’s annual test is in the Great Britain section of roadworthiness tests and roadside checks.

Which vehicles need the HGV, bus or trailer annual test?

GOV.UK’s overview says an HGV, bus or trailer MOT, “also known as an ‘annual test’”, is needed for:

  • vehicles that are built or have been adapted to form part of an articulated vehicle;
  • semi-trailers;
  • horseboxes with a gross weight of more than 3,500 kg;
  • “A” frame trailers and converter dollies manufactured on or after 1 January 1979;
  • trailers with an unladen weight of more than 1,020 kg with powered braking systems (instead of standard overrun brakes and as well as the required parking brake);
  • all public service vehicles, such as buses and coaches, with more than 8 passenger seats, not including the driver’s seat;
  • petrol, diesel and hybrid goods vehicles with a gross weight of more than 3,500 kg.

“Zero emission goods vehicles need a class 7 MOT if they have a design gross weight (DGW) between 3,501kg and 4,250kg.” For exemptions GOV.UK points to Form V112/G, adding that a vehicle exempt from the HGV MOT might still need a standard MOT; the form itself was not read for this article. The licence, operator licence and tachograph rules for horseboxes are in horsebox and horse trailer rules in Great Britain.

Due dates. “HGVs and buses (including coaches) usually must be tested each year. The first test should be 12 months after the vehicle was first registered with the Driver and Vehicle Licensing Agency”. “Trailers must usually be tested one year after they were first sold or supplied.” GOV.UK also says the inside of the vehicle must be cleaned before the test, and that the test will be cancelled and paid for again if the vehicle is not clean.

After the test. The Guide (section 6.2) says the test certificate is no longer printed when a vehicle passes; the result can be viewed, downloaded and printed from the MOT history service. A vehicle that fails gets documentation listing where it failed, and copies of the smoke test report and the brake test report can be asked for. Minor defects may be repaired during the test with the assessor’s permission, defects so serious that the vehicle cannot be moved on the public highway may lead to a prohibition, and defects that cannot be repaired at the time mean a retest. The test standards are in DVSA’s MOT inspection manuals for HGVs and for public service vehicles.

Ministry plates and plating certificates

DVSA’s guidance “HGV and trailer ministry plates and plating certificates”, updated on 1 June 2026 and applying to England, Scotland and Wales, covers goods vehicles and trailers; it does not deal with buses or coaches. It describes plates, “sometimes called ‘ministry plates’”, and plating certificates as “paper documents that show important information about the vehicle or trailer”, and says: “HGVs and trailers must have plates and plating certificates if they require an annual MOT.” Its list repeats the goods-vehicle and trailer entries of the MOT overview and adds “zero emission goods vehicles with a design gross weight of more than 4,250kg”.

The four plating documents in DVSA’s guidance (updated 1 June 2026).
DocumentReferenceWhat DVSA says to do with it
HGV plateVTG 6ADisplay in the vehicle’s cab, securely fixed, clear enough to read and in a position that is easy to see and read it from
HGV plating certificateVTG 7AKeep with the vehicle’s paperwork in the office or with the vehicle
Trailer plateVTG 6TDisplay on the trailer’s chassis, on the same conditions as the HGV plate
Trailer plating certificateVTG 7TKeep with the vehicle’s paperwork in the office or with the vehicle

The plate shows the serial number; the DTp reference number, which DVSA describes as a Department for Transport (DfT) number “related to the braking information”; the registration; the vehicle identification number (VIN); the manufacturer and model; whether it is exempt from needing a speed limiter; the function (rigid or articulated); the date of original registration; the year of manufacture; the gross weight, train weight and maximum train weight; the length and width; the axle weights; and conditions about the use of tyres. The plating certificate shows the same and also the tyre size and ply rating or load index. What gross and train weights mean is set out in truck weights: GVW and GCW. The maximum weights and dimensions that the Authorised Weight and Construction and Use Regulations allow in Great Britain are set out in lorry weight and size limits in Great Britain.

  • New HGV. The vehicle is registered with DVLA and its details are recorded with DVSA, which sends the plate and plating certificates. “There’s no fee for this.”
  • New trailer. “The trailer manufacturer must apply for the plate and plating certificate before they sell the trailer”, by applying to DVSA for permission to supply a large goods trailer for use on the road. There is no fee for this either.
  • Notifiable alterations. An updated plate and certificate are needed after a “notifiable alteration”, which includes changes to the chassis, the tyres, the brakes and the weight the vehicle can carry. DVSA’s terms: “up-plating” raises the maximum permitted weight without physical changes to the design, “uprating” raises it with the design modified, and “down-plating” and “downrating” reduce it without and with design changes, which DVSA says can lower the vehicle tax rate. “It costs £27.”
  • Mistakes. A correction is applied for with evidence: a photocopy of either the certificate of conformity or the IVA certificate, depending on how the vehicle was approved.
  • Lost or damaged. A copy of the plate and plating certificate can be downloaded as an A4 PDF, printed and displayed in the cab of an HGV or on the chassis of a trailer.

Roadside checks and the operator’s risk score

Both walkaround pages say the police and DVSA officers can stop a vehicle to check it, and that the driver can be stopped from driving until the problems found are fixed, or be fined. The Guide says DVSA uses the Operator Compliance Risk Score (OCRS) “to decide which vehicles should be inspected during roadside checks” (section 6.3), and lists annual test results, prohibitions and inspection notices among what an operator monitors (section 6.2). How the score is built and what earned recognition changes are in DVSA’s OCRS and earned recognition.

Quick answers

How often does an HGV need a safety inspection?
At the frequency the operator has recorded on the vehicle operator licensing service (VOL): DVSA's Guide to maintaining roadworthiness says operators must ensure safety inspections are carried out at that stated frequency. The Guide says an inspection frequency 'would normally range between 4 to 13 weeks', and its table of examples runs from 10-13 weeks for lightly loaded vehicles in easy operating conditions to 4 weeks off road in difficult conditions, and 6 weeks for vehicles and trailers 12 years or older. The table is guidance; the Guide says the 6-week frequency may be extended depending on usage, such as low mileage and light conditions.
Is the daily walkaround check a legal requirement?
DVSA's Guide says a driver or designated responsible person must conduct a walkaround check before the vehicle is used on the public highway, and it defines 'must' as a direct legal requirement. Section 3 of the Guide says a minimum of one walkaround check must be carried out every day or at least once in a 24-hour period that the vehicle is used. The Traffic Commissioners for Great Britain call the check a legal requirement and say it counts as working time. The Guide applies to England, Scotland and Wales.
How long must defect reports and safety inspection records be kept?
At least 15 months. DVSA's Guide says drivers' defect reports used to record faults and rectification work, and records of safety inspections, must be kept for at least 15 months; for safety inspection records it adds that this includes vehicles that have been removed from the operator licence, sold or otherwise disposed of. Brake-test risk assessments must be retained for 15 months. For 'nil' defect reports the Guide says it is recommended that they are retained for at least 3 months.
Which vehicles need an HGV, bus or trailer MOT?
GOV.UK lists petrol, diesel and hybrid goods vehicles with a gross weight of more than 3,500 kg, public service vehicles with more than 8 passenger seats not counting the driver's seat, semi-trailers, trailers over 1,020 kg unladen with powered braking systems, vehicles built or adapted to form part of an articulated vehicle, horseboxes over 3,500 kg, and A-frame trailers and converter dollies made on or after 1 January 1979. GOV.UK gives the first test as 12 months after first DVLA registration; trailers are usually tested one year after they were first sold or supplied. Zero emission goods vehicles with a design gross weight between 3,501 kg and 4,250 kg need a class 7 MOT.
What is a ministry plate on a lorry?
A paper document that DVSA calls an HGV or trailer plate, sometimes known as a 'ministry plate'. The HGV plate VTG 6A is displayed in the cab and the trailer plate VTG 6T on the trailer's chassis, with plating certificates VTG 7A and VTG 7T kept with the paperwork. They show details such as the gross weight, train weight, axle weights and the DTp reference number for the braking information. HGVs and trailers must have them if they require an annual MOT, and updating them after a notifiable alteration costs £27.
How many brake tests does an HGV need each year?
DVSA's Guide expects every safety inspection to include a brake performance assessment, by roller brake test, an electronic braking performance monitoring system (EBPMS) or a decelerometer with temperature readings. Where EBPMS is not used, it expects a minimum of four laden brake tests spread evenly across the year, which can include the annual test. For buses and coaches it expects an unladen roller brake test at every safety inspection; an operator that uses decelerometer assessments must carry out at least four roller brake tests a year.

Sources

  1. Guide to maintaining roadworthiness: commercial goods and passenger carrying vehicles (HTML edition, updated 28 April 2025) — GOV.UK (Driver and Vehicle Standards Agency)
  2. Keeping commercial vehicles safe to drive (roadworthy): publication page of the guide and its update log, last updated 28 April 2025 — GOV.UK (Driver and Vehicle Standards Agency)
  3. Get an MOT for a heavy goods vehicle (HGV), bus or trailer: Overview — GOV.UK
  4. HGV and trailer ministry plates and plating certificates (guidance, updated 1 June 2026) — GOV.UK (Driver and Vehicle Standards Agency)
  5. Carry out HGV daily walkaround checks (guidance, last updated 21 September 2023) — GOV.UK (Driver and Vehicle Standards Agency)
  6. Carry out bus or coach daily walkaround checks (guidance, last updated 18 April 2023) — GOV.UK (Driver and Vehicle Standards Agency)
  7. The Walkaround Check: A Legal Duty and Safety Priority (news story, 8 September 2025, updated 18 September 2025) — GOV.UK (Traffic Commissioners for Great Britain)